[PIE] LOOP CALIBRATOR PIECAL 532

HOME >

자.관련상품보기

전압전류교정기

[PIE] LOOP CALIBRATOR PIECAL 532

판매가: 견적문의

구매제한: 옵션당 최소 1개

구매혜택: 할인 : 적립 마일리지 :

배송비

0원 조건별배송

택배

/ 주문시결제(선결제)

방문 수령지 : 부산광역시 해운대구 우동1로20번가길 52-5(우동) 1층

상품코드: 2143

모델명: PIECAL 532

브랜드: PIE

제조사: PIE

원산지: 미국

상품상세정보
배송안내
교환 및 반품안내
상품후기 (0)
상품문의 (0)

상품상세정보

[PIE] LOOP CALIBRATOR PIECAL 532

mA/Voltage Loop Calibrator with Loop Diagnostics

제품특징

True ±0.012% of reading accuracy

Source and Read 0.000-24.000 mA

Simulate 2-Wire Transmitters Power 2-Wire Transmitters and Read 0.000-24.000mA

Display current in mA or -25.00-125.00 % of 4-20 mA

Read 0.00 to ± 30.00 VDC with 4X over range ability

Source 0.000 to 24.000 VDC with up to 20mA output

Direct Calibration 1.000V to 5.000V

Auto Step or Ramp

Selectable step sizes, time in-between steps & soak time

Full 5 Digit Display

Uses (1) 9 Volt alkaline battery

Superior battery life of 40 hours under typical continuous usage

Easy access to battery compartment

240 VAC Tolerant

Current Leak Detection

Check all loop parameters such as Current, Voltage, Resistance, AC Voltage and Ground Fault errors

The Piecal 532 4-20 mA/Voltage Loop Calibrator with Loop Diagnostics is the best tool for calibration, test, and diagnosing process loops. The Piecal 532 brings all the features you would expect from a loop calibrator and timesaving ones. Make adjustments with the EZ-Dial knob or test limits with the Dual Action EZ-Check switch. Powerful ramping functions are only a button away on the Piecal 532. Save potentially hours of troubleshooting time on problem loops with the Piecal 532’s unique Loop Diagnostic Mode.

In Piecal's 532 Loop Diagnostic Mode, the loop current, voltage, impedance, AC voltage, and mode of operation are all displayed simultaneously eliminating the need of a DMM connection. Loop diagnostics is available in every mode of operation and truly is a diagnostic monitor, as parameters are continuously updated in real time. The smart diagnostic tool even indicates the most likely cause of loop failure! Loop Diagnostic features the ability to measure ground fault error caused by faulty wiring, flooded conduit and corrosion bridges.

제품사양

Specifications
Function		Description
Common Specifications for all current modes
Ranges		00.000 to 24.000 mA
Accuracy		≤ ± (0.012 % of Reading + 0.004 mA)
Temperature effect		≤ ± 50 ppm/°C of Range
Resolution(s)		00.001 mA and 0.01%
Source/Power and Measure 2-Wire Transmitter Specifications
Loop Compliance Voltage		≥ 24 Volts
Loop Drive Capability		1200 Ω at 20 mA for entire battery life, 950Ω w/HART® mode enabled
Miscellaneous		Open loop or out of compliance conditions are indicated by appropriate error display
		Battery life in: Source mode ≥ 18 hrs at 12mA typical (HART disabled) Power measure ≥ 10 hrs at 12mA typical
		HART protocol mode is a selectable option at turn on. HART® protocol mode places a 250Ω resistor in series with the output
		Selectable EZ-Step(s) for Source Mode/2-Wire Transmitter Simulation: 2 to 16 selectable step settings (Step size is determined by the selected high & low ranges)
		Selectable time settings for stepping and soak: STEP: 5 to 900 seconds SOAK: 0 to 900 seconds
2-Wire Transmitter Simulation Specifications
Voltage Burden		≤ 2 V at 20 mA
Overload/Current Limit Protection		nominal ≤ 24 mA
Loop Voltage Limits		2-60 VDC
Miscellaneous		Open loop or out of compliance conditions are indicated by appropriate error display
		Battery life ≥ 40 hour typical
		Selectable EZ-Step(s) for Source Mode/2-Wire Transmitter Simulation
		2 to 16 selectable step settings: Step size is determined by the selected high & low ranges
		Selectable time settings for stepping and soak: STEP: 5 to 900 seconds SOAK: 0 to 900 seconds
Read mA Specifications
Voltage burden		≤ 2V at 20 mA
Overload/Current limit protection		nominal ≤24 mA
Battery life		Typical ≥ 40 Hours
Voltage Specifications
Source Range	Range	0.000 to 24.000 VDC
	Output Resistance	≤0.3 Ω
	Source Current	≥20.000 mA with Flashing indicator for over range
	Accuracy	≤±(0.012%RDG + 0.004 V) ±50ppm/°C of range
	Battery life	> 40 hour typical
Read Range	Range	0.000 to 24.000 VDC then 24.01 to 30.00 (with 4X over range) \| Auto Ranging
	Resolutions	0.001 V up to 24 V, 0.01 V up to 30.00 V
	Temperature Effect	≤ ± 100 ppm/°C of range
	Input Resistance	≥ 1 MΩ
	Accuracy	0.000 to 24.000 VDC ≤ ± (0.012%RDG + 0.004 V) 24.01 to 30.00 VDC ≤ ± (0.025 % of reading ±0.04 V)
Voltage burden		≤ 1V at 20 mA
Overload/Current Limit Protection		25 mA nominal
Loop Voltage Limits		2-42 VDC
Miscellaneous	Error Display	Open loop or out of compliance conditions are indicated by flashing the bar graph
	Battery life	≥ 40 hour typical
General Specifications: (Unless otherwise indicated all specifications are rated from a nominal 23 °C, 70 % RH for 1 year from calibration)
Temperature Range	Operating	-20 to 60 °C (-5 to 140 °F)
	Storage	-30 to 60 °C (-22 to 140 °F)
	Relative Humidity Range	10 % ≤RH ≤90 % (0 to 35 °C), Non-condensing
		10 % ≤RH≤ 70 % (35 to 60 °C), Non-condensing
Size		7.00 X 3.30 X 2.21 inches (177.8 x 83.8 x 56.1mm)
Weight		12.0 oz (340 grams)
Battery		9V Alkaline
		Optional 120 VAC 50/60 Hz AC adaptor available
Miscellaneous		Low battery indication with nominal 1 hour of operation left
		Over-voltage protection to 120 Vrms (rated for 30 seconds) or 240 Vrms (rated for 15 seconds)
		Bar graph display with 1% resolution of 4-20 mA signal scale
		High contrast graphic liquid crystal display with 0.45" (11.4 mm) high digits