[PIE] LOOP CALIBRATOR PIECAL 434

HOME >

자.관련상품보기

전압전류교정기

[PIE] LOOP CALIBRATOR PIECAL 434

판매가: 견적문의

구매제한: 옵션당 최소 1개

구매혜택: 할인 : 적립 마일리지 :

배송비

0원 조건별배송

택배

/ 주문시결제(선결제)

방문 수령지 : 부산광역시 해운대구 우동1로20번가길 52-5(우동) 1층

상품코드: 2142

모델명: PIECAL 434

브랜드: PIE

제조사: PIE

원산지: 미국

상품상세정보
배송안내
교환 및 반품안내
상품후기 (0)
상품문의 (0)

상품상세정보

[PIE] LOOP CALIBRATOR PIECAL 434

Automated 4-20mA Loop Calibrator with Loop Diagnostics

제품특징

Calibrate Milliamp Instruments: Source 0.000 to 24.000 mA & -25.00 to 125.00% of 4-20 mA Read 0.000 to 24.000 mA & -25.00 to 125.00% of 4-20 mA Read -99.99 to 99.99 V Simulate 2-Wire Transmitter, Power & Read Transmitters Menu Selectable 250 Ohm resistor for HART compatibility

Calibrate with Lab Accuracy: Accurate to ±(0.01% of Reading + 0.002 mA) PIECAL 434 is more accurate than similar calibrators - within ±0.004 mA at 20 mA output!

Easy-to-Read Backlit Display

Locate Loop Current Leakages: Automatic indication of Loop Current and Leakage Current. Measure ground current leakage from faulty wiring, flooded conduit and corrosion bridges. Leakage typically appears as a Zero Shift and helps you decide if the transmitter needs calibration or if there is a problem in the loop wiring.

Faster Calibrations: Three output EZ-CHECK switch 2 speed EZ-DIAL Stepping & Ramping

Includes Rubber Boot, Test Leads and hands free carrying case

제품사양

PIECAL 434 Specifications
General
Operating Temperature Range	-20 to 60 °C (-5 to 140 °F)
Storage Temperature Range	-30 to 60 °C (-22 to 140 °F)
Relative Humidity Range	10 % =RH =90 % (0 to 35 °C), Non-condensing
Relative Humidity Range	10 % =RH= 70 % (35 to 60 °C), Non-condensing
Size	5.63 x 3.00 x 1.60 in, 143 x 76 x 41mm (LxWxH)
Weight	12.1 ounces, 0.34 kg (including boot & batteries)
Batteries	Four “AA” Alkaline 1.5V (LR6)
Optional AC Adaptors	120 VAC 50/60 Hz [Part # 020-0100]
Optional AC Adaptors	240 VAC 50/60 Hz [Part # 020-0101]
Optional NiMh Rechargeable battery kit	120 VAC for North America Only; charger, four NiMh batteries, AC & DC cords [Part # 020-0103]
Low Battery	Low battery indication with nominal 1 hour of operation left
Protection against misconnection	Over-voltage protection to 135 vrms (rated for 30 seconds) or 240 vrms (rated for 15 seconds)
Display	High contrast graphic liquid crystal display with 0.315” (8.0 mm) high digits. LED backlighting for use in low lit areas.

Read mA
Ranges and Resolution	0.000 to 24.000 mA or -25.00 to 125.00% of 4-20 mA
Accuracy	= ± (0.01 % of Reading +0.002 mA)
Voltage burden	= 2V at 50 mA
Overload/Current limit protection	25 mA nominal
Battery life	= 125 Hours nominal
Battery life	= 100 hrs with backlight on

Source/Power & Measure Two Wire Transmitters
Ranges and Resolution	0.000 to 24.000 mA or -25.00 to 125.00% of 4-20 mA
Accuracy	= ± (0.01 % of Reading +0.002 mA)
Noise	= ± ½ Least Significant Digit
Temperature effect	= ± 0.005 %/°C of FS
Loop compliance voltage	= 24 DCV @ 20.00mA
Loop drive capability - Leak Detection Off	1200 O at 20 mA for 15 hours nominal; 950 O with Hart Resistor enabled
Loop drive capability - Leak Detection On	1000 O at 20 mA for 15 hours nominal; 750 O with Hart Resistor enabled
Battery life	= 30 hrs at 12 mA nominal; = 25 hrs with backlight on

2-Wire Transmitter Simulation
Accuracy	Same as Source/Power & Measure
Voltage burden	= 2V at 20 mA
Overload/Current limit protection	24 mA nominal
Loop voltage limits	2 to 60 VDC (fuse-less protected from reverse polarity connections)
Battery life	= 125 hours nominal; = 100 hrs with backlight on

Voltage Read
Range and Resolution	-60.00 to +60.00 VDC Full Span (FS)
Accuracy	= ± 0.05 % of FS
Temperature effect	= ± 100 ppm/°C of FS
Input resistance	= 2 MΩ
Battery life	= 125 hours nominal; = 100 hrs with backlight on